Dashboard trim panels — removal and installation Ford F150

Warning: The models covered in this manual are equipped with a Supplemental Restraint System (SRS), more commonly known as air bags. Always disable the airbag system before working in the vicinity of any airbag system component to avoid the possibility of accidental deployment of the airbags, which could cause personal injury (see Chassis electrical system).

1. Disconnect the cable from the negative battery terminal (see Battery and battery tray – removal and installation).

2. If equipped, remove the center console where necessary (see Center console – removal and installation).

Knee bolster

3. Use a dull, flat-bladed tool around the top of the knee bolster to release the clips, then lower the panel, disconnect the electrical connectors and remove the panel fasteners (see illustrations).

.3a Carefully release the clips and pull the panel off

Ford F150 Body_Dashboard trim panels - removal and installation _ Carefully release the clips and pull the panel off

.3b Disconnect the electrical connectors (1) and release the harness clips (2) from the panel

Ford F150 Body_Dashboard trim panels - removal and installation _ Disconnect the electrical connectors (1) and release the harness clips (2) from the panel

.3c Remove the bolts and knee bolster panel

Ford F150 Body_Dashboard trim panels - removal and installation _ Remove the bolts and knee bolster panel

4. Installation is the reverse of removal.

Instrument cluster finish panel

5. Remove the knee bolster (see Step 5).

6. Remove the panel mounting screws (see illustration).

.6 Instrument cluster finish panel mounting screw locations

Ford F150 Body_Dashboard trim panels - removal and installation _ Instrument cluster finish panel mounting screw locations

7. Carefully pry the finish panel out and remove it (see illustration).

.7 Using a trim tool, pry the trim panel out from the instrument panel

Ford F150 Body_Dashboard trim panels - removal and installation _ Using a trim tool, pry the trim panel out from the instrument panel

8. Installation is the reverse of removal.

Right side (glovebox) lower panel

9. Remove the plastic push pins the (see illustration), then remove the right side lower panel.

.9 Right side lower panel fastener locations

Ford F150 Body_Dashboard trim panels - removal and installation _ Right side lower panel fastener locations

10. Disconnect the electrical connector from the module, if equipped (see illustration).

.10 Disconnect the electrical connector from the module on the inside of the panel

Ford F150 Body_Dashboard trim panels - removal and installation _ Disconnect the electrical connector from the module on the inside of the panel

11. Installation is the reverse of removal.

Glove box

12. Remove the glove box hinge pins (see illustrations).

.12a Use a pair of pliers and compress the locking tabs…

Ford F150 Body_Dashboard trim panels - removal and installation _ Use a pair of pliers and compress the locking tabs

.12b…then pull the hinge pins out — right side shown, left side identical

Ford F150 Body_Dashboard trim panels - removal and installation _

13. Open the glove box door and remove the glove compartment dampener by pushing the end of the damper down and forward (see illustration).

.13 Push the end of the damper down and forward to disconnect it from the glove box

Ford F150 Body_Dashboard trim panels - removal and installation _ Push the end of the damper down and forward to disconnect it from the glove box

14. Push the sides of the glove box inwards until the stops (see illustration) are released.

.14 Push both sides in until the stops are released (right side shown, left side similar)

Ford F150 Body_Dashboard trim panels - removal and installation _ Push both sides in until the stops are released (right side shown, left side similar)

15. Lower the glove box and remove it from the hinges (see illustration).

.15 Lower the glove box until the hinges are free of the pivots, then pull off the glovebox

Ford F150 Body_Dashboard trim panels - removal and installation _ Lower the glove box until the hinges are free of the pivots, then pull off the glovebox

16. Installation is the reverse of removal.

Glove box

storage compartment

17. Open the glove box.

18. Use a trim stick (if necessary) to pry the storage compartment rubber trim panel off (see illustration).

23.18 Pry the storage compartment trim panel off

Ford F150 Body_Dashboard trim panels - removal and installation _ Pry the storage compartment trim panel off

19. Remove the two screws, pull the glove box storage compartment out (releasing it from the clips), then disconnect the electrical connector (see illustrations).

.19a Remove the storage compartment fasteners…

Ford F150 Body_Dashboard trim panels - removal and installation _ Remove the storage compartment fasteners

.19b…pull the storage compartment out of the instrument panel, releasing it from the retaining clips…

Ford F150 Body_Dashboard trim panels - removal and installation _

.19c…then disconnect the electrical connector.

Ford F150 Body_Dashboard trim panels - removal and installation _

20. Installation is the reverse of removal.

Upper dashboard storage compartment

21. Remove the mat from the upper storage compartment (see illustration).

.21 Lift the mat out from the upper storage compartment

Ford F150 Body_Dashboard trim panels - removal and installation _ Lift the mat out from the upper storage compartment

22. Remove the two screws from the upper storage compartment (see illustration).

.22 Location of the upper storage compartment screws

Ford F150 Body_Dashboard trim panels - removal and installation _ Location of the upper storage compartment screws

23. Use a plastic trim tool to pry the storage compartment out of the instrument panel (see illustration).

.23 Pry the storage compartment out of the instrument panel

Ford F150 Body_Dashboard trim panels - removal and installation _ Pry the storage compartment out of the instrument panel

24. Installation is the reverse of removal.

  • Pages

    Open all | Close all